[Q33-Q52] Fortinet NSE6_FNC-7.2 Dumps Updated [Oct-2024] Get 100% Real Exam Questions!

25Oct 2024 by admin No Comments

4.5/5 - (2 votes)

[Oct-2024] Pass Fortinet NSE6_FNC-7.2 Exam in First Attempt Guaranteed!

Full NSE6_FNC-7.2 Practice Test and 60 unique questions with explanations waiting just for you, get it now!

NO.33 While troubleshooting a network connectivity issue, an administrator determines that a device was being automatically provisioned to an incorrect VLAN.
Where would the administrator look to determine when and why FortiNAC made the network access change?

The Event view

The Admin Auditing view

The Port Changes view

The Connections view

NO.34 By default, if after a successful Layer 2 poll, more than 20 endpoints are seen connected on a single switch port simultaneously, what happens to the port?

The port becomes a threshold uplink

The port is disabled

The port is added to the Forced Registration group

The port is switched into the Dead-End VLAN

If more than 20 endpoints are seen connected on a single switch port simultaneously after a successful Layer 2 poll, the port is designated as an uplink. FortiNAC will ignore all physical addresses learned on an uplink port and will not perform any control operations on it

NO.35 What causes a host’s state to change to “at risk”?

The host has failed an endpoint compliance policy or admin scan.

The logged on user is not found in the Active Directory.

The host has been administratively disabled.

The host is not in the Registered Hosts group.

Failure – Indicates that the host has failed the scan. This option can also be set manually. When the status is set to Failure the host is marked “At Risk” for the selected scan.
Reference:
p. 244 of the Study Guide, “A state of at-risk indicates the host has failed a scan. This could be a compliance scan or an administrative scan.”

NO.36 What capability do logical networks provide?

Point of access-base autopopulation of device groups’

Interactive topology view diagrams

Application of different access values from a single access policy

IVLAN -based inventory reporting

Logical Networks allow you to create fewer Network Access Policies than before. (FortiNAC – What’s new in FortiNAC 7.2) Logical networks in FortiNAC decouple a policy from a specific access value, allowing for the application of different access values from a single access policy. This is done based on the point of connection, significantly reducing the number of network access policies needed and simplifying network access policy management

NO.37 Refer to the exhibit.

Considering the host status of the two hosts connected to the same wired port, what will happen if the port is a member of the Forced Registration port group?

The port will be provisioned for the normal state host, and both hosts will have access to that VLAN.

The port will not be managed, and an event will be generated.

The port will be provisioned to the registration network, and both hosts will be isolated.

The port will be administratively shut down.

NO.38 Which two policy types can be created on a FortiNAC Control Manager? (Choose two.)

Authentication

Network Access

Endpoint Compliance

Supplicant EasvConnect

Network Access policies as a common type of policy in FortiNAC, used to dynamically provision access to connecting endpoints. While Authentication is typically a policy type in network access control systems like FortiNAC

NO.39 How does FortiGate update FortiNAC about VPN session information?

API calls to FortiNAC

Syslog messages

SNMP traps

Security Fabric Integration

NO.40 What agent is required in order to detect an added USB drive?

Persistent

Dissolvable

Mobile

Passive

Expand the Persistent Agent folder. Select USB Detection from the tree.

NO.41 By default, if after a successful Layer 2 poll, more than 20 endpoints are seen connected on a single switch port simultaneously, what happens to the port?

The port becomes a threshold uplink

The port is disabled

The port is added to the Forced Registration group

The port is switched into the Dead-End VLAN

NO.42 How should you configure MAC notification traps on a supported switch?

Configure them only after you configure linkup and linkdown traps

Configure them only on ports set as 802 1q trunks

Configure them on all ports except uplink ports

Configure them on all ports on the switch

NO.43 Refer to the exhibit, and then answer the question below.

Which host is rogue?

NO.44 In which view would you find who made modifications to a Group?

The Event Management view

The Security Events view

The Alarms view

The Admin Auditing view

NO.45 Which agent can receive and display messages from FortiNAC to the end user?

Persistent

MDM

Passive

Dissolvable

NO.46 Which two of the following are required for endpoint compliance monitors? (Choose two.)

Persistent agent

Logged on user

Security rule

Custom scan

DirectDefense’s analysis of FireEye Endpoint attests that the products help meet the HIPAA Security Rule.
In the menu on the left click the + sign next to Endpoint Compliance to open it.
Reference:
https://docs.fortinet.com/document/fortinac/8.5.2/administration-guide/92047/add-or-modify-a-scan

NO.47 Which three of the following are components of a security rule? (Choose three.)

Security String

Methods

Action

User or host profile

Trigger

NO.48 Which system group will force at-risk hosts into the quarantine network, based on point of connection?

Forced Isolation

Physical Address Filtering

Forced Quarantine

Forced Remediation

NO.49 Which agent can receive and display messages from FortiNAC to the end user?

Dissolvable

Persistent

Passive

MDM

The persistent agent has the ability to display messages on the desktop of an endpoint. These messages can target an individual host, a group of hosts, or all hosts with the persistent agent installed. The messaging options include sending a message content with an optional web address link

NO.50 In an isolation VLAN which three services does FortiNAC supply? (Choose three.)

NTP

DHCP

Web

DNS

ISMTP

In an isolation VLAN, FortiNAC supplies DHCP and DNS services. The guide specifies that FortiNAC has a DHCP scope defined for a particular VLAN and should be the only DHCP server available to hosts on that VLAN. Additionally, hosts on the VLAN would get a DNS server configuration of the FortiNAC IP for that VLAN

NO.51 Where do you look to determine which network access policy, if any is being applied to a particular host?

The Policy Details view for the host

The Connections view

The Port Properties view of the hosts port

The Policy Logs view

FortiNAC p 382: “Under Network Access Settings – Policy Name – Name of the Network Access Policy that currently applies to the host.”

NO.52 By default, if more than 20 hosts are seen connected on a single port simultaneously, what will happen to the port?

The port is switched into the Dead-End VLAN.

The port becomes a threshold uplink.

The port is disabled.

The port is added to the Forced Registration group.

Loading …

Get Latest NSE6_FNC-7.2 Dumps Exam Questions in here: https://www.practicematerial.com/NSE6_FNC-7.2-exam-materials.html

Leave a Reply Cancel reply