PDI+ PD1-001 Exam Dumps and Certification Test Engine [Q129-Q150]

26Jun 2022 by admin No Comments

5/5 - (1 vote)

(PDF) PDI+ PD1-001 Exam and Certification Test Engine

Use PD1-001 Exam Dumps (2022 PDF Dumps) To Have Reliable PD1-001 Test Engine

NO.129 There is a number commonly listed on MOST packages of paper. Which of the following does this number indicate?

The brightness of the paper

The maximum percent of humidity of the paper

The speed at which the toner wil be fused with the media

The maximum print speed the paper can be used for

NO.130 Which of the following failed components would be responsible for media not being properly picked from the tray?

Paper feed unit

Transport roller

Registration sensor

Registration roller

NO.131 Which of the following reasons would the staple feature not be present in the print driver even though a stapler is fitted to the MFD?

The generic Windows driver needs the setting to be enabled.

The print server is unable to detect a staple unit.

The print driver is not for that particular model.

Stapling needs to be selected manually at the MFD.

NO.132 Which of the following procedures should be performed with the use of an anti-static wrist strap?

Replacing a circuit board

Cleaning the platen glass

Upgrading the firmware

Removing a paper tray

NO.133 A typical component used to generate heat in the fusing unit is a:

charging unit.

friction roller.

halogen lamp.

ceramic resistor.

NO.134 Which of the following does the dual component developer unit contain? (Select TWO).

Transfer roller

Developer

Charge roller

Photoconductor

Toner

NO.135 A customers copier says Add Paper even though the paper tray is full. Where MOST likely is the cause of the problem?

The sensor that tells the copier the tray is ful is broken or has failed.

The sensor in the duplex section shows paper already there.

The paper tray is set to a different paper size than requested.

The customer has left the original on the platen glass.

NO.136 Nozzles can be found on which of the following component?

Print head

Carriage unit

Purge unit

Carriage belt

NO.137 Which of the following is the purpose of a torque limiter in a roller?

To reduce wear and tear on rollers.

To provide resistance but still allow some slippage.

To limit the amount of movement by media.

To make it easier to replace rollers.

NO.138 Which of the following describes the purpose of the CCD?

To properly set the bias of the exposure lamp.

To properly set the bias voltages on the photoconductor.

To convert the scanned original image into an analog data stream.

To convert the scanned original image into a digital data stream.

NO.139 Which of the following compressed file formats creates the largest file size for a given document?

TIFF

PDF

JPEG

GIF

NO.140 A customer would like to use the scan-to-email function to allow them to search for email addresses within their company. Which of the following would need to be configured for the customer to utilize this function?

SSID

LDAP

POP3

SNMP

NO.141 A customer has a deadline to print a large job and their printer requires parts which will not arrive in time. They are very frustrated with the technician and the printer. Which of the following is the BEST response?

Explain the part wil be arriving the next day and the unit will be serviced at that time.

Explain there is nothing else that can be done and the customer wil have to deal with it.

Explain that there are other customers who also need attention and the schedule cannot be changed.

Empathize with the customers situation and suggest rerouting this job in order to meet the deadline.

NO.142 The latent image is created on the:

transfer belt.

developer unit.

fuser unit.

photoconductor.

NO.143 The purpose of the photoconductor preparation stage of the laser printing process is to: (Select TWO).

create a pattern of static charges that match the image to be developed on the photoconductor.

remove any remaining toner from the photoconductor.

eliminate residual charges from the previous process.

write a visible image on the photoconductor.

create a high level of static charges on the surface of the photoconductor.

NO.144 The print head moves left to right, drops down a line, then right to left. Which of the following represents this method of printing?

Unidirectional

Duplexing

Bi-directional

Dithering

NO.145 Which of the following are methods for dealing with ESD? (Select THREE).

Unplugging the power cord

Wearing rubber sole shoes

Using an anti-static mat

Wearing an anti-static wrist strap

Working on a metal table

Periodically touching a metal doorknob

NO.146 Which of the following is the purpose of the CCD in the scanner device?

To convert light into electrical signals

To identify the correct file format

To detect different colors

To focus the light beam

NO.147 Which of the following devices can route electrical signals only when activated by an external control signal?

Solenoid

Relay

Clutch

Capacitor

NO.148 Which of the following processes occurs inside the dual component developer unit during printing?

The developer and toner are cleaned.

A high bias voltage is placed on the magnetic roller.

The developer is measure for proper temperature.

A low bias voltage is placed on the agitator roller.

NO.149 While onsite a technician discovers the customer is in the process of evaluating a printer from a competitor. Which of the following should be done?

Cal the customers manager and advise them of the situation.

Ask the customer if a sales representative may call them.

Refuse to do anything and call the service manager.

Tell the customer that the new printer is of poor quality.

NO.150 On a four-color, subtractive color printing device, a green test page is printing yellow. Which of the following colors is missing from the test print?

Magenta

Black

Red

Cyan

Loading …

PD1-001 Dumps Full Questions with Free PDF Questions to Pass: https://www.practicematerial.com/PD1-001-exam-materials.html

Leave a Reply Cancel reply