Check Real Fortinet NSE7_PBC-6.4 Exam Question for Free (2023) [Q17-Q33]

19May 2023 by admin No Comments

5/5 - (2 votes)

Check Real Fortinet NSE7_PBC-6.4 Exam Question for Free (2023)

Get Ready to Boost your Prepare for your NSE7_PBC-6.4 Exam with 30 Questions

NEW QUESTION 17
What is the bandwidth limitation of an Amazon Web Services (AWS) transit gateway VPC attachment?

Up to 1.25 Gbps per attachment

Up to 50 Gbps per attachment

Up to 10 Gbps per attachment

Up to 1 Gbps per attachment

NEW QUESTION 18
Which two statements about Amazon Web Services (AWS) networking are correct? (Choose two.)

Proxy ARP entries are disregarded.

802.1q VLAN tags are allowed inside the same virtual private cloud.

AWS DNS reserves the first host IP address of each subnet.

Multicast traffic is not allowed.

NEW QUESTION 19
Refer to the exhibit.

You are configuring an active-passive FortiGate clustering protocol (FGCP) HA configuration in a single availability zone in Amazon Web Services (AWS), using a cloud formation template.
After deploying the template, you notice that the AWS console has IP information listed in the FortiGate VM firewalls in the HA configuration. However, within the configuration of FortiOS, you notice that port1 is using an IP of 10.0.0.13, and port2 is using an IP of 10.0.1.13.
What should you do to correct this issue?

Configure FortiOS to use static IP addresses with the IP addresses reflected in the ENI primary IP address configuration (as per the exhibit).

Delete the deployment and start again. You have in put the wrong parameters during the cloud formation template deployment.

Configure FortiOS to use DHCP so that it will get the correct IP addresses on the ports.

Nothing, in AWS cloud, it is normal for a FortiGate ENI primary IP address to be different than the FortiOS IP address configuration.

NEW QUESTION 20
Refer to the exhibit.

A customer has deployed an environment in Amazon Web Services (AWS) and is now trying to send outbound traffic from the Web servers to the Internet. The FortiGate policies are configured to allow all outbound traffic; however, the traffic is not reaching the FortiGate internal interface.
What are two possible reasons for this behavior? (Choose two.)

The web servers are not configured with the default gateway.

The Internet gateway (IGW) is not added to VPC (virtual private cloud).

AWS source and destination checks are enabled on the FortiGate interfaces.

AWS security groups may be blocking the traffic.

NEW QUESTION 21
Refer to the exhibit.

The exhibit shows a topology where multiple connections from clients to the same FortiGate-VM instance, regardless of the protocol being used, are required.
Which two statements are correct? (Choose two.)

The design shows an active-active FortiGate-VM architecture.

The Cloud Load Balancer Session Affinity setting should be changed to CLIENT_IP.

The design shows an active-passive FortiGate-VM architecture.

The Cloud Load Balancer Session Affinity setting should use the default value.

NEW QUESTION 22
You are deploying Amazon Web Services (AWS) GuardDuty to monitor malicious or unauthorized behaviors related to AWS resources. You will also use the Fortinet aws-lambda-guarddutyscript to translate feeds from AWS GuardDuty findings into a list of malicious IP addresses. FortiGate can then consume this list as an external threat feed.
Which Amazon AWS services must you subscribe to in order to use this feature?

GuardDuty, CloudWatch, S3, Inspector, WAF, and Shield.

GuardDuty, CloudWatch, S3, and DynamoDB.

Inspector, Shield, GuardDuty, S3, and DynamoDB.

WAF, Shield, GuardDuty, S3, and DynamoDB.

NEW QUESTION 23
Refer to the exhibit.

In your Amazon Web Services (AWS) virtual private cloud (VPC), you must allow outbound access to the internet and upgrade software on an EC2 instance, without using a NAT instance. This specific EC2 instance is running in a private subnet: 10.0.1.0/24.
Also, you must ensure that the EC2 instance source IP address is not exposed to the public internet. There are two subnets in this VPC in the same availability zone, named public (10.0.0.0/24) and private (10.0.1.0/24).
How do you achieve this outcome with minimum configuration?

Deploy a NAT gateway with an EIP in the private subnet, edit the public main routing table, and change the destination route 0.0.0.0/0 to the target NAT gateway.

Deploy a NAT gateway with an EIP in the public subnet, edit route tables, select Public-route, and delete the route destination 10.0.0.0/16 to target local.

Deploy a NAT gateway with an EIP in the private subnet, edit route tables, select Private-route, and add a new route destination 0.0.0.0/0 to the target internet gateway.

Deploy a NAT gateway with an EIP in the public subnet, edit route tables, select Private-route and add a new route destination 0.0.0.0/0 to target the NAT gateway.

NEW QUESTION 24
Your company deploys FortiGate VM devices in high availability (HA) (active-active) mode with Microsoft Azure load balancers using the Microsoft Azure ARM template. Your senior administrator instructs you to connect to one of the FortiGate devices and configure the necessary firewall rules. However, you are not sure now to obtain the correct public IP address of the deployed FortiGate VM and identify the access ports.
How do you obtain the public IP address of the FortiGate VM and identify the correct ports to access the device?

In the configured load balancer, access the inbound NAT rules section.

In the configured load balancer, access the backend pools section.

In the configured load balancer, access the inbound and outbound NAT rules section.

In the configured load balancer, access the health probes section.

NEW QUESTION 25
A company deployed a FortiGate-VM with an on-demand license using Amazon Web Services (AWS) Market Place Cloud Formation template. After deployment, the administrator cannot remember the default admin password.
What is the default admin password for the FortiGate-VM instance?

The admin password cannot be recovered and the customer needs to deploy the FortiGate-VM again.

<blank>

admin

The instance-ID value

NEW QUESTION 26
A company deployed a FortiGate-VM with an on-demand license using Amazon Web Services (AWS) Market Place Cloud Formation template. After deployment, the administrator cannot remember the default admin password.
What is the default admin password for the FortiGate-VM instance?

The admin password cannot be recovered and the customer needs to deploy the FortiGate-VM again.

<blank>

admin

The instance-ID value

NEW QUESTION 27
Which two statements about Microsoft Azure network security groups are true? (Choose two.)

Network security groups can be applied to subnets and virtual network interfaces.

Network security groups can be applied to subnets only.

Network security groups are stateless inbound and outbound rules used for traffic filtering.

Network security groups are a stateful inbound and outbound rules used for traffic filtering.

NEW QUESTION 28
You have been tasked with deploying FortiGate VMs in a highly available topology on the Amazon Web Services (AWS) cloud. The requirements for your deployment are as follows:
* You must deploy two FortiGate VMs in a single virtual private cloud (VPC), with an external elastic load balancer which will distribute ingress traffic from the internet to both FortiGate VMs in an active-active topology.
* Each FortiGate VM must have two elastic network interfaces: one will connect to a public subnet and other will connect to a private subnet.
* To maintain high availability, you must deploy the FortiGate VMs in two different availability zones.
How many public and private subnets will you need to configure within the VPC?

One public subnet and two private subnets

Two public subnets and one private subnet

Two public subnets and two private subnets

One public subnet and one private subnet

NEW QUESTION 29
Which two Amazon Web Services (AWS) topologies support east-west traffic inspection within the AWS cloud by the FortiGate VM? (Choose two.)

A single VPC deployment with multiple subnets and a NAT gateway

A single VPC deployment with multiple subnets

A multiple VPC deployment utilizing a transit VPC topology

A multiple VPC deployment utilizing a transit gateway

NEW QUESTION 30
Refer to the exhibit.

You are deploying a FortiGate-VM in Microsoft Azure using the PAYG/On-demand licensing model. After you configure the FortiGate-VM, the validation process fails, displaying the error shown in the exhibit.
What caused the validation process to fail?

You selected the incorrect resource group.

You selected the Bring Your Own License (BYOL) licensing mode.

You selected the PAYG/On-demand licensing model, but did not select correct virtual machine size.

You selected the PAYG/On-demand licensing model, but did not associate a valid Azure subscription.

NEW QUESTION 31
Customer XYZ has an ExpressRoute connection from Microsoft Azure to a data center. They want to secure communication over ExpressRoute, and to install an in-line FortiGate to perform intrusion prevention system (IPS) and antivirus scanning.
Which three methods can the customer use to ensure that all traffic from the data center is sent through FortiGate over ExpressRoute? (Choose three.)

Install FortiGate in Azure and build a VPN tunnel to the data center over ExpressRoute

Configure a user-defined route table

Enable the redirect option in ExpressRoute to send data center traffic to a user-defined route table

Configure the gateway subnet as the subnet in the user-defined route table

Define a default route where the next hop IP is the FortiGate WAN interface

NEW QUESTION 32
When an organization deploys a FortiGate-VM in a high availability (HA) (active/active) architecture in Microsoft Azure, they need to determine the default timeout values of the load balancer probes.
In the event of failure, how long will Azure take to mark a FortiGate-VM as unhealthy, considering the default timeout values?

Less than 10 seconds

30 seconds

20 seconds

16 seconds

NEW QUESTION 33
Refer to the exhibit.

The exhibit shows a topology where multiple connections from clients to the same FortiGate-VM instance, regardless of the protocol being used, are required.
Which two statements are correct? (Choose two.)

The design shows an active-active FortiGate-VM architecture.

The Cloud Load Balancer Session Affinity setting should be changed to CLIENT_IP.

The design shows an active-passive FortiGate-VM architecture.

The Cloud Load Balancer Session Affinity setting should use the default value.

The Fortinet NSE7_PBC-6.4 Certification Exam is designed to test the skills and knowledge of security professionals who specialize in public cloud security. The exam covers a wide range of topics, including cloud security architecture, virtualization, automation, and orchestration. Candidates who pass the exam will demonstrate their ability to design, implement, and manage security solutions for public cloud environments using Fortinet products and technologies.

The Fortinet NSE7_PBC-6.4 exam is a challenging exam that requires candidates to have a deep understanding of public cloud security concepts, as well as hands-on experience with Fortinet’s public cloud security solutions. The exam consists of multiple-choice questions, and candidates are required to answer 60 questions in 120 minutes.

Use Free NSE7_PBC-6.4 Exam Questions that Stimulates Actual EXAM : https://www.practicematerial.com/NSE7_PBC-6.4-exam-materials.html

Leave a Reply Cancel reply