[2023] Free 300-410 Exam Dumps to Pass Exam Easily [Q158-Q175]

03Aug 2023 by admin No Comments

4.3/5 - (3 votes)

[2023] Free 300-410 Exam Dumps to Pass Exam Easily

300-410 Exam Dumps, 300-410 Practice Test Questions

Cisco 300-410 (Implementing Cisco Enterprise Advanced Routing and Services) Certification Exam is a professional-level certification that is designed to validate the skills and knowledge of network engineers who are responsible for implementing advanced routing and services in enterprise networks. 300-410 exam is ideal for network professionals who have a good understanding of network protocols, routing, and switching technologies, and are looking to enhance their skills in advanced routing and services.

QUESTION 158
Exhibit:

BGP is flapping after the Copp policy is applied. What are the two solutions to fix the issue?
(Choose two)

Configure a three-color policer instead of two-color policer under Class COPP-CRIT1CAL-7600

Configure IP CEF for CoPP policy and BGP to work

Configure a higher value for CIR under the default class to allow more packets during peak traffic

Configure a higher value for CIR under the Class COPP-CRIT1CAL-7600

Configure BGP in the COPP-CRIT1CAL-7600 ACL

QUESTION 159
Refer to the exhibit.

R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1. What action will fix the issue?

Fix route dampening configured on the router.

Replace the SFP module because it is not supported.

Fix IP Event Dampening configured on the interface.

Correct the IP SLA probe that failed.

QUESTION 160
Refer to the exhibit.

Why is the remote NetFlow server failing to receive the NetFlow data?

The flow exporter is configured but is not used.

The flow monitor is applied in the wrong direction.

The flow monitor is applied to the wrong interface.

The destination of the flow exporter is not reachable.

QUESTION 161
Refer to the exhibit.

An administrator is troubleshooting a time synchronization problem for the router time to another Cisco IOS XE-based device that has recently undergone hardening. Which action resolves the issue?

Allow NTP in the ingress ACL on 10.1.225.40 by permitting UDP destined to port 123.

Ensure that he CPE router has a valid route to 10.1.255. 40 for NTP and rectify if not reachable.

NTP service is disabled and must be enabled on 10.1.225.40.

Allow NTP in the ingress ACL on 10.1.255.40 by permitting TCP destined to port 123.

QUESTION 162
Drag and drop the operations from the left onto the locations where the operations are performed on the right.

QUESTION 163
Refer to the exhibit.

The network engineer configured the summarization of the RIP routes into the OSPF domain on R5 but still sees four different 172.16.0.0/24 networks on R4. Which action resolves the issue?

R5(config)#router ospf 1
R5(config-router)#no area
R5(config-router)#summary-address 172.16.0.0 255.255.252.0

R4(config)#router ospf 99
R4(config-router)#network 172.16.0.0 0.255.255.255 area 56
R4(config-router)#area 56 range 172.16.0.0 255,255.255.0

R4(config)#router ospf 1
R4(config-router)#no area
R4(config-router)#summary-address 172.16.0.0 255.255.252.0

R5(config)#router ospf 99
R5(config-router)#network 172.16.0.0 0.255.255.255 area 56
R5(config-router)#area 56 range 172.16.0.0 255.255.255.0

QUESTION 164
Refer to the exhibit.

A)

B)

C)

D)

Option

QUESTION 165
Refer to the exhibit.

Refer to the exhibit. Router R4 is configured correctly with default OSPF values. A network engineer configured R7 for OSPF. R7 must not be elected as a DR for the segment between R4-R7. The adjacency between R4 and R7 failed to form. Which configuration resolves the issue?

Option A

Option B

Option C

Option D

QUESTION 166
Refer to the exhibit.

Which interface configuration must be configured on the space A route enable a dynamic DMVPN tunnel with the spoke B router?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

QUESTION 167
Drag and drop the MPLS VPN device types from me left onto the definitions on the right.

QUESTION 168
Refer to the exhibit.

Refer to the exhibit SW100 cannot receive routes from R1 Which configuration resolves the issue?

Option A

Option B

Option C

QUESTION 169
Refer to Exhibit.

Which statement about redistribution from BGP into OSPF process 10 is true?

Network 172.16.1.0/24 is not redistributed into OSPF.

Network 10.10 10.0/24 is not redistributed into OSPF

Network 172.16.1.0/24 is redistributed with administrative distance of 1.

Network 10.10.10.0/24 is redistributed with administrative distance of 20.

QUESTION 170
Refer to the exhibit.

The server for the finance department is not reachable consistently on the 200.30.40.0/24 network and after every second month it gets a new IP address. Which two actions must be taken to resolve this Issue? (Choose two.)

Configure the server to use DHCP on the network with default gateway 200 30.40.100.

Configure the server with a static IP address and default gateway.

Configure the router to exclude a server IP address.

Configure the server to use DHCP on the network with default gateway 200 30.30.100.

Configure the router to exclude a server IP address and default gateway.

QUESTION 171
Refer to the exhibit.

An engineer must establish a point-to-point GRE VPN between R1 and the remote site. Which configuration accomplishes the task for the remote site?

Interface Tunnel1
tunnel source 199.1.1.1
tunnel destination 200.1.1.3
ip address 192.168.1.3 255.255.255.0

Interface Tunnel1
tunnel source 200.1.1.3
tunnel destination 199.1.1.1
ip address 192.168.1.1.255.255.255.0

Interface Tunnel1
tunnel source 200.1.1.3
tunnel destination 199.1.1.1
ip address 192.168.1.3.255.255.255.0

Interface Tunnel
lunnel source 199.1.1.1
tunnel destination 200.1.1.3
ip address 192.168.1.1.255.255.255.0

QUESTION 172
Refer to the exhibit.
The administrator noticed that the connection was flapping between the two ISPs instead of switching to ISP2 when the ISP1 failed. Which action resolves the issue?

Include a valid source-interface keyword in the icmp-echo statement.

Reference the track object 1 on the default route through ISP2 instead of ISP1.

Modify the static routes to refer both to the next hop and the outgoing intertace.

Modify the threshold to match the administrative distance of the ISP2 route.

QUESTION 173
Refer to the exhibit.

An IP SLA was configured on router R1 that allows the default route to be modified in the event that Fa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through router R2. Which debug command is used to troubleshoot this issue?

debug ip flow

debug ip sla error

debug ip routing

debug ip packet

QUESTION 174
Drag and drop the packet types from the left onto the correct descriptions on the right.

Explanation

Unlike legacy network technologies such as ISDN, Frame Relay, and ATM that defined separate data and control channels, IP carries all packets within a single pipe. Thus, IP network devices such as routers and switches must be able to distinguish between data plane, control plane, and management plane packets to treat each packet appropriately.From an IP traffic plane perspective, packets may be divided into four distinct, logical groups:1. Data plane packets – End-station, user-generated packets that are always forwarded by network devices to other end-station devices. From the perspective of the network device, data plane packets always have a transit destination IP address and can be handled by normal, destination IP address-based forwarding processes.2. Control plane packets – Network device generated or received packets that are used for the creation and operation of the network itself. From the perspective of the network device, control plane packets always have a receive destination IP address and are handled by the CPU in the network device route processor. Examples include protocols such as ARP, BGP, OSPF, and other protocols that glue the network together.3. Management plane packets – Network device generated or received packets, or management station generated or received packets that are used to manage the network. From the perspective of the network device, management plane packets always have a receive destination IP address and are handled by the CPU in the network device route processor. Examples include protocols such as Telnet, Secure Shell (SSH), TFTP, SNMP, FTP, NTP, and other protocols used to manage the device and/or network.4. Services plane packets – A special case of data plane packets, services plane packets are also user-generated packets that are also forwarded by network devices to other end-station devices, but that require high-touch handling by the network device (above and beyond normal, destination IP address-based forwarding) to forward the packet. Examples of high-touch handling include such functions as GRE encapsulation, QoS, MPLS VPNs, and SSL/IPsec encryption/decryption, etc. From the perspective of the network device, services plane packets may have a transit destination IP address, or may have a receive destination IP address (for example, in the case of a VPN tunnel endpoint).

QUESTION 175
How does an MPLS Layer 3 VPN differentiate the IP address space used between each VPN?

by RD

by address family

by MP-BGP

byRT

300-410 Exam Dumps, 300-410 Practice Test Questions: https://www.practicematerial.com/300-410-exam-materials.html

Leave a Reply Cancel reply