Get The Most Updated 156-836 Dumps To CCME Certification [Q37-Q60]

30Nov 2024 by admin No Comments

4.5/5 - (2 votes)

Get The Most Updated 156-836 Dumps To CCME Certification

CheckPoint Certified 156-836 Dumps Questions Valid 156-836 Materials

The Check Point Certified Maestro Expert – R81 (CCME) exam is a comprehensive certification exam that covers a wide range of topics related to the Maestro platform. 156-836 exam tests the candidate’s knowledge of Maestro architecture, deployment models, and management capabilities. It also covers topics such as high availability, load balancing, and failover mechanisms. 156-836 exam requires candidates to have a strong understanding of networking and security concepts, as well as experience working with Check Point technologies. Overall, the Check Point Certified Maestro Expert – R81 (CCME) exam is a highly respected certification that validates the candidate’s ability to work with advanced security technologies and manage large-scale security deployments.

CheckPoint 156-836 certification exam is designed to validate the knowledge and skills of IT professionals in deploying and managing Check Point Maestro, a network security orchestration solution. Check Point Certified Maestro Expert – R81 (CCME) certification exam is designed for individuals who have already obtained the Check Point Certified Security Expert (CCSE) certification and have experience in managing Check Point products. Check Point Certified Maestro Expert – R81 (CCME) certification exam tests the candidate’s knowledge in network segmentation, traffic management, and deployment of Maestro gateways.

QUESTION 37
What is the purpose of g_tcpdump command?

Collects traffic dump from Sync network

Collects traffic dump from CIN network

The same as tcpdump, just on Scalable Platform

Collects traffic dump from all Active Appliances within Security Group

QUESTION 38
Which command should be used to restart Orchestrator service only?

orchd restart

reboot

service orchestrator restart

cpstop; cpstart

QUESTION 39
What is the maximum number of Appliances within Security group in Dual-Site configuration?

QUESTION 40
What is the purpose of Management ports located on the Rear Panel of the Orchestrator MHO-140?

1Gbps connectivity for Security Groups

Reserved for internal purposes. Not in use.

Out-of-band interfaces for access to Orchestrator itself

Additional ports used as uplinks

QUESTION 41
The drop_monitor command is useful for

Monitoring Check Point code drops

Viewing all interface drops such as RX-ERR, RX-DRP, and RX-OVR

Viewing all drops by Check Point code or the Gaia OS, such as RX-DRP, RX-ERR, and Gaia OS drops.

Showing the system temperature in real-time for multiple components, such as CPU, fan, and SSDs.

QUESTION 42
What happens when you make changes from Clish on the SMO Master?

The changes are synchronized to the SMS/MDS as a backup.

The changes are synchronized to the MHO as a backup.

Changes are only applied on the SMO Master.

Changes are applied to all members in the SG.

QUESTION 43
While looking at your system’s correction statistics, you notice you have a correction rate approaching 100 percent. Is this a problem?

A correction rate above 90 percent indicates a need to disable Layer 4 Distribution.

A correction rate approaching 100 percent of all connections is unusual. This is a cause for concern because the SGMs may fail to process traffic.

If correction rates are higher than 80 percent, latency is expected.

In some scenarios, a correction rate approaching 100 percent of all connections is not unusual. This is not usually a cause for concern as the correction mechanism is fast and efficient.

QUESTION 44
Multiple SGs can exist in a Dual Site environment. Each SG can be configured in one of three ways. Which is not one of those ways?

Two MHOs connected to two MHOs via load balancers.

Two MHOs at same site connected to remote site MHOs via two different switches.

Two MHOs at same site connected to remote site MHOs via single switch.

Direct connectivity between Remote Site MHOs.

QUESTION 45
Where should sx_api_ports_dump.py command be ran?

Management server

Security Group

Orchestrator

SMO Appliance

QUESTION 46
What is the command ‘asg diag’ used for?

Asg diag used for system diagnostics on Chassis only. It does not exist on Maestro

Asg diag is used for system backup

Asg diag is used for system diagnostics

Asg diag is used for creating traffic flow diagrams

QUESTION 47
Splitter cannot be used _______

To connect single port on orchestrator to the same Appliance

To connect single port on orchestrator to multiple port on external switch

To connect single port on Appliance to multiple ports on the orchestrator

To connect single port on orchestrator to multiple Appliances

QUESTION 48
What is the purpose of RJ-45 connectors located at the front panel of the Orchestrator MHO-170?

Two Out-of-band interfaces for access to Orchestrator itself

1Gbps connectivity for Security Groups

Out-of-band interface for access to Orchestrator itself and Serial Console connector

Reserved for internal purposes. Not in use

QUESTION 49
There are two 10Gbps dual-port NICs and one 40Gbps NIC installed on a 23800 Appliance in slots 1, 2 and 3 accordingly. Which interfaces should be connected to Orchestrator 1 for downlinks’ intra- orchestrator redundancy when using two Orchestrators?

Port 1 in Slot 2 and Port 2 in Slot 1

This configuration is not supported

Any pair of available ports

Port 1 in Slot 1 and Port 2 in Slot 1

QUESTION 50
What cannot be learned from the output of asg monitor command?

Uptime

Port status

Security Policy status

Appliances cluster status

QUESTION 51
What kinds of transceivers are supported on Orchestrator MHO-170?

SFP, QSFP, QSFP28

SFP+, SFP28, QSFP

SFP, SFP+, SFP28

QSFP, QSFP28

QUESTION 52
When security policy is installed

All SGMs receive the security policy and one by one performs an independent policy verification. Then, all SGMs simultaneously install the policy.

The SMO Master receives the policy and performs a policy verification the policy is installed on the SMO Master, the SMO Master broadcasts the available package, other membersretrieve the new policy from the SMO Master, then the non-SMO Master SGMs install the policy.

All SGMs receive the security policy and simultaneous policy installation occurs.

The policy is installed on the SMO, the SMO Master broadcasts the available package, other members retrieve the new policy from the SMO Master and perform an independent policy verification, then the non-SMO Master SGMs install the policy.

QUESTION 53
There are two appliances within the same Security Group. One of them is connected by One downlink only, another one by Two downlinks. Assuming there’s no NAT and no VPN, what would be proportion of traffic distribution done by Orchestrator?

100%/0%

33%/66%

50%/50%

66%/33%

QUESTION 54
When working with Maestro, what is the difference between using Clish and gClish?

Clish commands are for testing purposes only and cannot be saved, gClish commands apply to all SG members, by default.

Clish commands apply to all UP SG members, by default. gClish commands apply to all SG members, by default.

Clish commands are run on the SG members. gClish commands are run on the MHO and applied to all connected SG members in a specified group.

Clish commands apply only to a specific SG member. gClish commands apply to all UP SG members, by default.

QUESTION 55
What is the default Distribution mode?

Auto-topology

User

Manual-General

Network

QUESTION 56
HealthCheck Point _____

is a self-updatable suite of tools for MHOs with the capability to assess the health of the system and provide a timeline of critical and informative events that might have occurred in a production system.

performs a system health check and is meant to replace both a CPInfo and the health check script.

can be used to let you visualize the Firewall topology for the SG and view live statistics, which includes throughput, problem notes, and CPU utilization.

is a self-updatable suite of tools for SGMs with the capability to assess the health of the system, visualize the Firewall topology, provide a timeline of critical and informative events that might have occurred in a production system.

QUESTION 57
After you import the R81.10 software package, what do you use to verify that it is possible to upgrade an MHO or SG?

Run HCP. One of the tests will list upgrade eligibility status for the MHO or SG.

Run the Pre-Upgrade Verifier to make sure it is possible to upgrade

Nothing. CPUSE will run a verification during the upgrade process to ensure the package is compatible.

The package is verified during the import process and a warning or error will be displayed at that time.

QUESTION 58
Possibilities for a failure in a single SGM of a Security Group include.

A change was made with clish instead of gClish, causing the SGM to handle traffic differently than the other SGMs.

SecureXL is not enabled on the SGM.

An administrator imported a hotfix into the CPUSE repository of a single SGM.

There are too many active SGMs in the SG.

QUESTION 59
Logs without a dedicated log file can be found in

/var/log/junk.log.dbg

/var/log/messages

$RTDIR/log/junk.log

$FWDIR/log/fw.log

QUESTION 60
What kinds of transceivers are supported on Orchestrator MHO-140?

SFP, QSFP, QSFP28

SFP+, SFP28, QSFP

SFP, SFP+, SFP28

SFP, SFP+, QSFP, QSFP28

156-836 Premium PDF & Test Engine Files with 77 Questions & Answers: https://www.practicematerial.com/156-836-exam-materials.html

Leave a Reply Cancel reply