[Q15-Q29] Latest Fortinet NSE7_OTS-7.2 First Attempt, Exam real Dumps Updated [Aug-2025]

17Aug 2025 by admin No Comments

4.7/5 - (3 votes)

Latest Fortinet NSE7_OTS-7.2 First Attempt, Exam real Dumps Updated [Aug-2025]

Get the superior quality NSE7_OTS-7.2 Dumps Questions from PracticeMaterial. Nobody can stop you from getting to your dreams now. Your bright future is just a click away!

QUESTION 15
As an OT administrator, it is important to understand how industrial protocols work in an OT network. Which communication method is used by the Modbus protocol?

It uses OSI Layer 2 and the primary device sends data based on request from secondary device.

It uses OSI Layer 2 and both the primary/secondary devices always send data during the communication.

It uses OSI Layer 2 and both the primary/secondary devices send data based on a matching token ring.

It uses OSI Layer 2 and the secondary device sends data based on request from primary device.

QUESTION 16
An OT supervisor has configured LDAP and FSSO for the authentication. The goal is that all the users be authenticated against passive authentication first and, if passive authentication is not successful, then users should be challenged with active authentication.
What should the OT supervisor do to achieve this on FortiGate?

Configure a firewall policy with LDAP users and place it on the top of list of firewall policies.

Enable two-factor authentication with FSSO.

Configure a firewall policy with FSSO users and place it on the top of list of firewall policies.

Under config user settings configure set auth-on-demand implicit.

QUESTION 17
As an OT network administrator, you are managing three FortiGate devices that each protect different levels on the Purdue model. To increase traffic visibility, you are required to implement additional security measures to detect exploits that affect PLCs.
Which security sensor must implement to detect these types of industrial exploits?

Intrusion prevention system (IPS)

Deep packet inspection (DPI)

Antivirus inspection

Application control

QUESTION 18
As an OT network administrator you are managing three FortiGate devices that each protect different levels on the Purdue model To increase traffic visibility you are required to implement additional security measures to detect protocols from PLCs Which security sensor must you implement to detect protocols on the OT network?

Endpoint Detection and Response (EDR)

Deep packet inspection (DPI)

Intrusion prevention system (IPS)

Application control (AC)

QUESTION 19
Which three Fortinet products can you use for device identification in an OT industrial control system (ICS)? (Choose three.)

FortiSIEM

FortiManager

FortiAnalyzer

FortiGate

FortiNAC

QUESTION 20
Which three common breach points can you find in a typical OT environment? (Choose three.)

Black hat

VLAN exploits

Global hat

RTU exploits

Hard hat

QUESTION 21
Refer to the exhibit. An OT administrator ran a report to identify device inventory in an OT network.
Based on the report results, which report was run?

A FortiSIEM CMDB report

A FortiAnalyzer device report

A FortiSIEM incident report

A FortiSIEM analytics report

QUESTION 22
With the limit of using one firewall device, the administrator enables multi-VDOM on FortiGate to provide independent multiple security domains to each ICS network. Which statement ensures security protection is in place for all ICS networks?

Each traffic VDOM must have a direct connection to FortiGuard services to receive the required security updates.

The management VDOM must have access to all global security services.

Each VDOM must have an independent security license.

Traffic between VDOMs must pass through the physical interfaces of FortiGate to check for security incidents.

QUESTION 23
What two advantages does FortiNAC provide in the OT network? (Choose two.)

It can be used for IoT device detection.

It can be used for industrial intrusion detection and prevention.

It can be used for network micro-segmentation.

It can be used for device profiling.

QUESTION 24
Refer to the exhibit. An OT network security audit concluded that the application sensor requires changes to ensure the correct security action is committed against the overrides filters.
Which change must the OT network administrator make?

Set all application categories to apply default actions.

Change the security action of the industrial category to monitor.

Set the priority of the C.BO.NA.1 signature override to 1.

Remove IEC.60870.5.104 Information.Transfer from the first filter override.

The application sensor settings allow you to configure the security action for each application category and network protocol override. The security action determines how the FortiGate unit handles traffic that matches the application category or network protocol override. The security action can be one of the following:
Allow: The FortiGate unit allows the traffic without any further inspection. Monitor: The FortiGate unit allows the traffic and logs it for monitoring purposes.
Block: The FortiGate unit blocks the traffic and logs it as an attack. The priority of the network protocol override determines the order in which the FortiGate unit applies the security action to the traffic. The lower the priority number, the higher the priority. For example, a priority of 1 is higher than a priority of 10. In the exhibit, the application sensor has the following settings:
The industrial category has a security action of allow, which means that the FortiGate unit will not inspect or log any traffic that belongs to this category. The IEC.60870.5.104 Information.Transfer network protocol override has a security action of block, which means that the FortiGate unit will block and log any traffic that matches this protocol. The IEC.60870.5.104 Control.Functions network protocol override has a security action of monitor, which means that the FortiGate unit will allow and log any traffic that matches this protocol. The IEC.60870.5.104 Start/Stop network protocol override has a security action of allow, which means that the FortiGate unit will not inspect or log any traffic that matches this protocol. The IEC.60870.5.104 Transfer.C.BO.NA.1 network protocol override has a security action of block, which means that the FortiGate unit will block and log any traffic that matches this protocol. The problem with these settings is that the IEC.60870.5.104 Transfer.C.BO.NA.1 network protocol override has a lower priority than the IEC.60870.5.104 Information.Transfer network protocol override. This means that if the traffic matches both protocols, the FortiGate unit will apply the security action of the higher priority override, which is block. However, the IEC.60870.5.104 Transfer.C.BO.NA.1 protocol is used to transfer binary outputs, which are essential for controlling OT devices. Therefore, blocking this protocol could have negative consequences for the OT network. To fix this issue, the OT network administrator must set the priority of the IEC.60870.5.104 Transfer.C.BO.NA.1 network protocol override to 1, which is higher than the priority of the IEC.60870.5.104 Information.Transfer network protocol override. This way, the FortiGate unit will apply the security action of the lower priority override, which is allow, to the traffic that matches both protocols. This will ensure that the FortiGate unit does not block the traffic that is used to transfer binary outputs, while still blocking the traffic that is used to transfer information.

QUESTION 25
Which two statements about the Modbus protocol are true? (Choose two.)

Modbus uses UDP frames to transport MBAP and function codes.

Most of the PLC brands come with a built-in Modbus module.

You can implement Modbus networking settings on internetworking devices.

Modbus is used to establish communication between intelligent devices.

QUESTION 26
What two advantages does FortiNAC provide in the OT network? (Choose two.)

It can be used for IoT device detection.

It can be used for industrial intrusion detection and prevention.

It can be used for network micro-segmentation.

It can be used for device profiling.

QUESTION 27
Refer to the exhibit.
An OT architect has implemented a Modbus TCP with a simulation server Conpot to identify and control the Modus traffic in the OT network. The FortiGate-Edge device is configured with a software switch interface ssw-01.
Based on the topology shown in the exhibit, which two statements about the successful simulation of traffic between client and server are true? (Choose two.)

The FortiGate-Edge device must be in NAT mode.

NAT is disabled in the FortiGate firewall policy from port3 to ssw-01.

The FortiGate devices is in offline IDS mode.

Port5 is not a member of the software switch.

QUESTION 28
A supervisor is configuring a software switch on a FortiGate device. What must the supervisor configure on FortiGate to control the traffic between member interfaces on the software switch, using firewall policies?

The supervisor must add different VLAN interfaces to the software switch.

The supervisor must configure the software switch with at least one wireless interface and one VLAN interface.

The supervisor must configure a separate forward domain for the software switch.

The supervisor must configure intra-switch-policy to explicit.

QUESTION 29
Refer to the exhibit.
Given the configurations on the FortiGate, which statement is true?

FortiGate is configured with forward-domains to reduce unnecessary traffic.

FortiGate is configured with forward-domains to forward only domain controller traffic.

FortiGate is configured with forward-domains to forward only company domain website traffic.

FortiGate is configured with forward-domains to filter and drop non-domain controller traffic.

Guaranteed Success with Valid Fortinet NSE7_OTS-7.2 Dumps: https://www.practicematerial.com/NSE7_OTS-7.2-exam-materials.html

Leave a Reply Cancel reply