Free 2026 API Certification API-1169 dumps are available by PracticeMaterial [Q236-Q259]

07Nov 2026 by admin No Comments

Rate this post

Free 2026 API Certification API-1169 dumps are available on Google Drive shared by PracticeMaterial

Welcome to download the newest PracticeMaterial API-1169 PDF dumps: https://www.practicematerial.com/API-1169-exam-materials.html ( 453 Q&As)

API API-1169 Exam Syllabus Topics:

Section	Objectives
Pipeline Construction Practices	– Pipe installation and assembly methods – Right-of-way (ROW) preparation and excavation – Welding and joining processes overview
Pipeline Construction Codes and Standards	– API standards applicable to pipeline construction – Regulatory requirements and compliance frameworks
Inspection and Quality Control	– Inspection procedures and documentation – Non-destructive testing (NDT) methods – Defect identification and remediation
Safety and Environmental Compliance	– Occupational safety requirements – Environmental protection during construction
Project Management and Documentation	– Construction records and reporting – Project coordination and communication

NEW QUESTION 236
Define specification in terms related to data information and document

Data supporting the existence of verity of something(Objective evidence can be obtained through observation measurement test or by other means)(ISO 9000 3.8.3)

Lifting/hoisting pipe and equipment, excavation your pipe lines or other utilities, marking/labeling, and other programs to increase awareness

Within 2 feet of the existing facilities or the distance mandated by state law which ever is greater(INGAA CROSSING guide 11 K)

Document stating requirements(example quality manual, quality plan, technical drawing, procedure document, work instruction.)(ISO 9000 3.8.7)

NEW QUESTION 237
Flammable Liquids

Area where the ground disturbance occurs within 50, of centerline of ROW, facility or easement

Class 1 liquids having a flash point below 100 deg F. Gasoline.

gouges, buckles, wrinkles, ripples or ovality,s

Minimum specified distance from welds and ends. Bending increments are distributed along length of bend.

NEW QUESTION 238
The cross company will identify areas where blasting will be used along the route within how many feet of the existing facilities to be crossed?

Is the vertical separation between the existing pipeline and facilities and where the new pipeline is being installed. The recommended crossing clearance distance between the new pipeline and the existing facilities is two feet (24″). The minimum distance is one foot (12″). The new pipeline should be installed at a level depth across the ROW, if practicable.

300, (the members recognize this guideline differs from the one contained in the API,s “Guidelines for Property Development” that specifies a hosting plan is required when blasting will occur within a (1/4) mile of existing facilities.

Efforts to notify the excavator by phone, email, or using a contact card on a string, or other comparable method, on the door handle, or steering wheel, of the subject equipment.

Action to illuminate the cause of a potential nonconformity or other potential undesirable situation.(Preventative action is taken to prevent occurrence were as correct of action is taken to prevent recurrence)(ISO 9000 3.12.1)

NEW QUESTION 239
Cathodic protection test stations are typically installed every?

rework(api 1104 3.1.25)

98 to 3 kilometres(cepa 16.1)

12 inches(api 1169 7.15)

2 to 3 kilometres(CEPA 16.1)

NEW QUESTION 240
Yellow

Sewers and Drain Lines

Gas, Oil, Steam, Petroleum or Gaseous Materials

gouges, buckles, wrinkles, ripples or ovality,s

Electric Power Lines, Cables, Conduit and Lighting Cables

NEW QUESTION 241
What is the primary issue that must be addressed with Crossing navigable waters with a natural gas pipeline?

A diffuser (general knowledge)

Msds(general knowledge)

Safety concerns(general knowledge)

The quality policy(iso 9000 3.5.8)

NEW QUESTION 242
Define Excavation Tolerance Zone

Is the area in which soil must be removed by non-mechanical means such as (hand digging, pot-holing, or hydro-Vac) rather than mechanical means. It is an area within 2 feet of the existing facilities or the distance mandated by state law where applicable, whichever is greater.

Is the singular point of contact identified within the company of the crossing company and the owner who has the responsibility to communicate about the safely managed crossing. There will be a cross and Company designated contact and an owner designated contact.

Is the area where the edge of the disturbance is within 25 feet of the centreline of the existing facilities.

NEW QUESTION 243
How many feet would be between 58+00 to 68+00

120

300

990

1000

NEW QUESTION 244
Class Soil Rock
Class 1
Class 2, 3, 4
Drainage ditches of public roads and railroad crossings

Class Soil RockClass 1 30 (762) 18 (457)Class 2, 3, 4 36 (914) 24 (610)Drainage ditches of public roads and railroad crossings36 (914) 24 (610)

The transmission line must be protected.Subpart G 192.325

Indicate whether power or hand tools are to be used

5% of volume

NEW QUESTION 245
Hazard recognition by inspector -hot weather (health), cold weather,

Climatic and other work condition hazards

Unconfined compressive state

Required reporting

Noxious weeds and soil pests

NEW QUESTION 246
Know about;
-National _________ preservation act
-___________ Species act
-Resource _________ and Recovery Act
-Comprehensive _________ Recovery, Compensation and ________ Act

A pressure just above test pressure

-Historic-Endangered-Conservation-

Temporary trench plugs / segment

100s of feet with additional footage shown as pulses

NEW QUESTION 247
Work Permits for excavation would be found under what OSHA standard?

OSHA 1910.109 and OSHA 1926.900 to 1926.914

OSHA 1926.650 and 1926.651, (29 CFR 1926) safety and health regulations for construction

Part of quality management focused on fulfilling quality requirements(ISO 9000 3.3.7)

Have the longitude a weld as near as practical to the neutral axis of the band(49 CFR 192.313)

NEW QUESTION 248
Orange

Sewers and Drain Lines

Occupational Safety and Hazard Administration

Potable Water

Communication, Alarm or Signal Lines

NEW QUESTION 249
Examples of information discussed and exchange between Designated contacts include?

Management with regard to quality, can include establishing quality policies in quality objectives and processes to achieve these quality objectives through quality planning quality assurance quality control and quality improvement(ISO 9000 3.3.4)

Placement of the ROW, Location of the existing of proposed pipelines within the ROW, the types of easement (exclusive, or open and undefined), construction methods and practices, unique landscape, terrain, or environmental situations, separation distances, restrictions on type in location of heavy equipment crossings, any potential pipeline integrity concerns, responsibility for cathodic protection after installation, the ground disturbance timing.

Is the entity that intends to install, operate, maintain a new pipeline that crosses existing pipeline facilities. The Crossing company may designate a third-party or parties to perform the task necessary to accomplish a Crossing but remains responsible for the work performed by such third parties.

Document stating requirements(example quality manual, quality plan, technical drawing, procedure document, work instruction.)(ISO 9000 3.8.7)

NEW QUESTION 250
Define validation in terms related related to data, information and document.

Confirmation, through the provisions of objective evidence, that the requirements for a specific intended use or application have been fulfilled.(The objective evidence needed for a validation is the result of a test or other form of determination such as performing alternative calculations or reviewing documents)(ISO 9000 3.8.13)

Confirmation, through the provisions of objective evidence, that specified requirements have been fulfilled.(The objective evidence needed for a fair if Acacian can be the result of an inspection or of other forms of determination such as performing alternative calculations or reviewing documents)(ISO 9000 3.8.12)

Document stating requirements(example quality manual, quality plan, technical drawing, procedure document, work instruction.)(ISO 9000 3.8.7)

NEW QUESTION 251
Color used for surveyed electrical lines

Green

White

Red

Yellow

NEW QUESTION 252
Rework is:
-Filing the toes of the weld to create the correct profile
-Grinding or welding on a completed weld that was rejected by examination
-The removal of imperfections prior to visual on NDT examination
-Any grinding or welding on a completed weld to correct potentially rejectable indications

grind or sand the surface to bare metal prior to welding.

The removal of imperfections prior to visual or NDT examination

it provides proper support for the pipe and prevents damage to the pipe and its coating

Understanding of permit documentation requirements

NEW QUESTION 253
If screw anchors are to be installed, the inspector shall ensure?

That the trench is adequately sloped, and access/egress ladders are installed.(CEPA TABLE 74)

OSHA 1926.650 and 1926.651, (29 CFR 1926) safety and health regulations for construction

Safety to the public(ASME B31.4 443.2, API 1169 7.3.1)

Part of quality management focussed on providing confidence that quality requirements will be fulfilled.(ISO 9000 3.3.6)

NEW QUESTION 254
Top soil must be segregated to ________ inches

NEW QUESTION 255
Welder,s re-qualifying period is based on whether the pipe pressure produces a hoop stress of __________ than ______% of SMYS

more or less / 10

more or less / 20

more or less / 19

more or less / 120

NEW QUESTION 256
Hearing protection during a hydro test requirement state that the protection must be adequate to reduce the noise to at least below ____ decibels.

NEW QUESTION 257
Portions of piping systems to be operated at a hoop stress of more than __________ of the SMYS of the pipe shall be subjected at any point to a hydrostatic proof test equivalent to not less than 1.25 times the internal design pressure?
-25%
-30%
-80%
-50%
-None of these

Pipe facing

All of the above

Pressure testing

None of these

NEW QUESTION 258
Focused on increasing the ability to fulfill quality requirements.

Quality planning

Quality improvement

Cost reduction

Quality control

NEW QUESTION 259
How is pipe stationing typically shown?
-10s of feet with add ft as 0s
-10s of feet with add ft shown as pluses
-100s of feet with add shown as zeros
-100s of feet with add shown as pulses

1972 / 1. coating / 2. cathodic protection

100s of feet with additional footage shown as pulses

The different types and agency jurisdiction

6.625 in OD and .250 in wall thickness

Tested Material Used To API-1169: https://www.practicematerial.com/API-1169-exam-materials.html

API API-1169 Exam Syllabus Topics:

Leave a Reply Cancel reply